TLE2141QDRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100, Excalibur™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | TLE2141 |
| Pin Count | 8 |
| Operating Supply Voltage | 22V |
| Number of Elements | 1 |
| Power Supplies | +-2/+-22/4/44V |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 4.5mA |
| Output Current | 50mA |
| Slew Rate | 45V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 700nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.4mV |
| Gain Bandwidth Product | 5.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 6000 kHz |
| Voltage Gain | 106.85dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 2μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 5.8MHz |
| Max I/O Voltage | 1.4mV |
| Wideband | NO |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLE2141QDRQ1 Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. The pins on this board total to 8 in total. Please take in mind that this instrumentation amplifier should be run at 15V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. In total, the buffer amplifier consists of 8 pins. Op amp rates 1.4mV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. As long as the supply current of the chip does not exceed 3.5mA, this op amp ic can operate. You should keep the voltage gain at 106.85dB for the time being. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 1. The operating supply voltage of the buffer op amp is rated at 22V. It is used TR to pack the op amps. Automotive, AEC-Q100, Excalibur? corresponds to linear amplifier's series.
TLE2141QDRQ1 Features
8 Pins
supply voltage of 15V
106.85dB voltage gain
TLE2141QDRQ1 Applications
There are a lot of Texas Instruments TLE2141QDRQ1 Instrumentational OP Amps applications.
- Car stereo
- Video amplifiers
- Differentiator circuits
- Video data acquisition
- Portable electronic products powered by batteries
- Radar
- Thermocouples
- Computer workstations
- Signal operation
- Blood pressure sensors
