TLE2142CPWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Series | Excalibur™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TLE2142 |
| Pin Count | 16 |
| Operating Supply Voltage | 22V |
| Power Supplies | 5/+-15V |
| Number of Circuits | 2 |
| Operating Supply Current | 6.9mA |
| Nominal Supply Current | 9mA |
| Output Current | 50mA |
| Slew Rate | 45V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 700nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 290μV |
| Bandwidth | 5.8MHz |
| Gain Bandwidth Product | 5.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 6000 kHz |
| Voltage Gain | 106.85dB |
| Average Bias Current-Max (IIB) | 1.6μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 5.8MHz |
| Max I/O Voltage | 1.9mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.1μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLE2142CPWR Overview
A 16-TSSOP (0.173, 4.40mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 16 terminations have been reported in the past few weeks. A total of 16 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 16 pins on it. Op amp rates 290μV as input offset voltage. This electrical part should be mounted using type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. You can run this op amp ic on 6.9mA . The voltage gain should stay at 106.85dB. The buffer amp consists of 2 circuits in total. The operating supply voltage of instrumentation amplifier is rated 22V voltage. TR is adopted to pack the instrumentation amplifier. In this case, Excalibur? represents the instrumentation amplifiers' series number.
TLE2142CPWR Features
16 Pins
supply voltage of 15V
106.85dB voltage gain
TLE2142CPWR Applications
There are a lot of Texas Instruments TLE2142CPWR Instrumentational OP Amps applications.
- Oscilloscopes
- High input resistance broadband
- Hand-held batteries
- Test and measurement instruments
- Laptop
- Image computer boards
- Gaming industry
- Computer workstations
- Inverse/same-phase proportional circuit
- Voltage regulation circuit
