TLE2144CDWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Series | Excalibur™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLE2144 |
| Pin Count | 16 |
| Operating Supply Voltage | 22V |
| Power Supplies | 5/+-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 13.8mA |
| Nominal Supply Current | 18mA |
| Output Current | 50mA |
| Slew Rate | 45V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 700nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 600μV |
| Bandwidth | 5.8MHz |
| Gain Bandwidth Product | 5.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 6000 kHz |
| Voltage Gain | 99.55dB |
| Average Bias Current-Max (IIB) | 1.6μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 2μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 5.8MHz |
| Max I/O Voltage | 3.8mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.1μA |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLE2144CDWRG4 Overview
The linear amplifier is packaged in a 16-SOIC (0.295, 7.50mm Width) case which makes it easy for the consumer to handle. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 16 terminations have been reported in the past few weeks. In this case, there are 16 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. It should be noted that this op amp is a type of Operational Amplifier device. An 16-pin op amp ic is included in the package. Op amp rates 600μV as input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . An 13.8mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. On this instrumentation amplifier, there are 4 circuits that are connected together. The operating supply voltage of instrumentation amplifier is rated 22V voltage. TR is adopted to pack the instrumentation amplifier. This buffer amplifier is assigned within the Excalibur? series by its manufacturer.
TLE2144CDWRG4 Features
16 Pins
supply voltage of 15V
99.55dB voltage gain
TLE2144CDWRG4 Applications
There are a lot of Texas Instruments TLE2144CDWRG4 Instrumentational OP Amps applications.
- High input resistance broadband
- Power control
- Inverse/same-phase proportional circuit
- Division circuits
- Medical instruments
- Exponential operation circuits
- Biopotential
- PDA
- High/low-pass filter circuit
- Ultrasound transducers
