TLE824533SAAUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 36-BSSOP (0.433, 11.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 36 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Number of Outputs | 6 |
| Output Type | N-Channel |
| Max Output Current | 1.5A |
| Supply Voltage-Max (Vsup) | 5.25V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Number of Channels | 3 |
| Interface | SPI |
| Output Configuration | High Side or Low Side |
| Output Current | 1.6A |
| Voltage - Supply (Vcc/Vdd) | 4.75V~5.25V |
| Quiescent Current | 8mA |
| Switch Type | Relay, Solenoid Driver |
| Halogen Free | Halogen Free |
| Ratio - Input:Output | 1:3 |
| Voltage - Load | 8V~17V |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Screening Level | AEC-Q100 |
| Rds On (Typ) | 250m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Supply Voltage1-Min | 8V |
| Supply Voltage1-Max | 17V |
| Length | 15.9mm |
| Width | 11mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TLE824533SAAUMA1 Overview
It is package in Tape & Reel (TR) case.In the 36-BSSOP (0.433, 11.00mm Width) Exposed Pad package, it is included.It has been mounted as Surface Mount on the LED driver.There is a switch type of Relay, Solenoid Driver.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.By default, it is set to output 6.In order to operate, it requires a voltage supply of 4.75V~5.25V.A maximum output voltage of N-Channel volts can be achieved by this LED driver.Currently, the LED driving board is equipped with Status Flag features.The termination count is 36.The 36 pins are used to operate the LED driver.The LED driver has 1 functions.This operation requires the maximum output current to be decreased to 1.5A.The supply voltage can be 5V for high efficiency.This case has the output current set to 1.6A.A maximum supply voltage of 5.25V is set in Vsup.In order to operate normally, the supply voltage (Vsup) must be maintained above 4.75V.The total number of channels is 3.
TLE824533SAAUMA1 Features
Supplied from 5V
3 channels
TLE824533SAAUMA1 Applications
There are a lot of Infineon Technologies TLE824533SAAUMA1 Power Switches ICs applications.
- Portable/Handheld Devices
- PC Cards
- Portable GPS Device
- Wireless Headsets
- Hard Disk Drives
- USB Ports/Hubs
- Solid-State Drives
- PDAs
- Various applications equipped with buttons
- Solid State Drivers
