TLE83862ELXUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-LSSOP (0.154, 3.90mm Width) Exposed Pad |
| Number of Pins | 14 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLE8386 |
| Function | Step-Up |
| Number of Outputs | 1 |
| Output Voltage | 5.5V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 45V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 50mA |
| Voltage - Supply (Vcc/Vdd) | 4.75V~45V |
| Control Features | Enable, Frequency Control, Soft Start |
| Input Voltage (Min) | 4.75V |
| Topology | Boost |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 100kHz~700kHz |
| Halogen Free | Halogen Free |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 93 % |
| Clock Sync | Yes |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLE83862ELXUMA1 Overview
With a 14-LSSOP (0.154, 3.90mm Width) Exposed Pad package, the switching controller is suitable for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. Tape & Reel (TR) solid enclosure protects the pmic. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching's4.75V~45V is the supply voltage and the operating voltage of the dc control. A -40°C~150°C TJ dc switcher is not a problem. A switching controller such as this can switch at a value of 100kHz~700kHz . The Surface Mount allows it to be used for dc dc regulator in general. Featured in the dcdc regulator is Enable, Frequency Control, Soft Start which allows efficient switching control. The switch converters are connected to a SWITCHING CONTROLLER analog IC. There are a DUAL terminal on the switching converters. The 14 terminations can be used for a wide range of dc switching. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 6V. TLE8386 can be used to locate other relevant dc to dc converter ics. 14 pins are on switching converter. It is recommended to use 4.75V as the minimum input voltage of dc dc voltage regulator. The test statistics indicate that DC regulator outputs a voltage of 5.5V. A starting point for a project is to note down the dc dc regulator's usual output current, which is 50mA. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 93 % during power-up and power-down. The Surface Mount makes DC switcher suitable for most applications and prototypes. To run the voltage regulator dc to dc safely and reliably, users should apply 45V to the voltage regulator dc to dc.
TLE83862ELXUMA1 Features
Transistor Driver Outputs
Switching Frequency: 100kHz~700kHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 93 %
TLE83862ELXUMA1 Applications
There are a lot of Infineon Technologies TLE83862ELXUMA1 DC to DC converter applications.
- Textile machinery
- Smoke prevention equipment
- Power supplies of electronic gadgets
- Low output voltage switching power supply circuits
- Surface processing equipment
- Hydraulic presses
- Various precision measuring instruments
- Overvoltage protection circuits in TV sets
- Terrestrial set-top boxes
- Electrical power transmission
