TLV2231CDBVT
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2231 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Operating Supply Current | 850μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 150mW |
| Output Current | 50mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1.9MHz |
| Gain Bandwidth Product | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 112.04dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 710μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 3V |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
TLV2231CDBVT Overview
In the package, you will find a SC-74A, SOT-753-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. A Tape & Reel (TR) case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 5. The pins on this board total to 5 in total. The linear amplifier should be run at 3V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 5 pins on this chip. Op amp ic rates 3mV for input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . Operational amplifier can operate supply current at 850μA. There should be no change in the voltage gain at 112.04dB. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. It is possible to count 1 elements on this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 5V voltage. This linear amplifier pack is based on the TR axis. LinCMOS? corresponds to the op amp's series.
TLV2231CDBVT Features
5 Pins
supply voltage of 3V
112.04dB voltage gain
Output Type: Rail-to-Rail
TLV2231CDBVT Applications
There are a lot of Texas Instruments TLV2231CDBVT Instrumentational OP Amps applications.
- Division circuits
- Signal amplification
- Information processing
- Portable docking station
- Precision measurement
- Digital cameras
- Comparator
- pH (acidity)
- Hand-held batteries
- Fission chambers
