TLV2242IDGKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLV2242 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 2.5μA |
| Power Dissipation | 481mW |
| Output Current | 200μA |
| Slew Rate | 0.002V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 55 dB |
| Current - Input Bias | 100pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~12V ±1.25V~6V |
| Output Current per Channel | 200μA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 5.5 kHz |
| Unity Gain BW-Nom | 5.5 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 16.5V |
| Voltage - Input Offset | 600μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 5.5 kHz |
| Max I/O Voltage | 3mV |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2242IDGKR Overview
Op amp is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. A General Purpose-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. A total of 8 terminations have been reported in the past few weeks. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 2.7V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 3mV. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. This op amp can operate from a supply current at 1μA. There should be no change in the voltage gain. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 6V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
TLV2242IDGKR Features
8 Pins
supply voltage of 2.7V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2242IDGKR Applications
There are a lot of Texas Instruments TLV2242IDGKR Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Medical imaging
- Large motor controllers
- single/dual op amp sum and difference circuits
- Precision measurement
- Strain gauges
- Oscilloscopes
- Medical instruments
- Cinema or auditorium audio system
- Voltage regulation circuit
