TLV2361IDBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.5V |
| Base Part Number | TLV2361 |
| Pin Count | 5 |
| Operating Supply Voltage | 2.5V |
| Number of Circuits | 1 |
| Operating Supply Current | 1.75mA |
| Nominal Supply Current | 2.5mA |
| Output Current | 20mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | ±1V~2.5V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 6MHz |
| Gain Bandwidth Product | 7MHz |
| Neg Supply Voltage-Nom (Vsup) | -1.5V |
| Unity Gain BW-Nom | 7000 kHz |
| Voltage Gain | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 6MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2361IDBVR Overview
In the package, you will find a SC-74A, SOT-753-case to contain the op amp ic. An op amp of this type is a General Purpose-type. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. It is estimated that there will be 5 terminations in the next few months. A total of 5 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 1.5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. A total of 5 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 1mV. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. An 1.75mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 80dB. The buffer amp consists of 1 circuits in total. The operating supply voltage of instrumentation amplifier is rated 2.5V voltage. The linear amplifier is packaged by using a TR axis.
TLV2361IDBVR Features
5 Pins
supply voltage of 1.5V
80dB voltage gain
TLV2361IDBVR Applications
There are a lot of Texas Instruments TLV2361IDBVR Instrumentational OP Amps applications.
- pH (acidity)
- Displayers for aircraft and air transportation control systems
- Automation control systems
- Band-stop filter
- Portable media players
- Non-polarized electrodes
- Cinema or auditorium audio system
- Signal filtering
- Power transmission
- Fast A/D and D/A converters
