TLV2372IDG4
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 1.8mA |
| Power Dissipation | 710mW |
| Current - Output | 16mA |
| Slew Rate | 2 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 60pA |
| Output Current per Channel | 16mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 2.4MHz |
| Gain Bandwidth Product | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 8V |
| Low-Bias | YES |
| Micropower | NO |
| Min Dual Supply Voltage | 1.35V |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 4.5mV |
| Height | 1.58mm |
| Length | 4.9mm |
| Width | 3.91mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Package / Case | SOIC |
| Surface Mount | YES |
| Number of Pins | 8 |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
TLV2372IDG4 Overview
The linear amplifier is packaged in a SOIC case which makes it easy for the consumer to handle. Buffer amps of this type are called OPERATIONAL AMPLIFIER-types. As far as the packaging is concerned, buffer op amp is delivered in a Rail/Tube case. We are approaching the 8h termination of the year. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 4.5mV. It is possible to operate this buffer amplifier from a supply current of 750μA . Keeping the voltage gain at 110dB is the best course of action. This instrumentation amplifier cannot operate below -40°C degrees Celsius. At temperatures greater than 125°C, op amp should not be used. The buffer op amp is rated for an operating voltage of 2 when it comes to the power supply. The operating supply voltage of instrumentation amplifier is rated 8V voltage. Under 16V is the minimum supply voltage for this electric component. It is advised to keep the op amp's supply voltage higher than 2.7V. This electronic part should be conducted with a dual supply voltage of 8V volts for this part.
TLV2372IDG4 Features
8 Pins
supply voltage of 5V
110dB voltage gain
TLV2372IDG4 Applications
There are a lot of Texas Instruments TLV2372IDG4 Instrumentational OP Amps applications.
- Video amplifiers
- High gain DC amplifier
- Computer workstations
- Proportional counter tubes
- Weak signal detection
- Micro signal measurement
- Automotive sensors
- Video computer boards
- Tablets
- Weighing systems
