TLV2402CDR
| Parameters | |
|---|---|
| Current - Supply | 900nA |
| Slew Rate | 0.0025V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 100pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~16V ±1.25V~8V |
| Output Current per Channel | 200μA |
| Input Offset Voltage (Vos) | 1.2mV |
| Bandwidth | 5.5 kHz |
| Gain Bandwidth Product | 5.5kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Voltage - Input Offset | 390μV |
| Current - Output / Channel | 200μA |
| Max Dual Supply Voltage | 8V |
| Min Dual Supply Voltage | 1.25V |
| Nominal Gain Bandwidth Product | 5.5 kHz |
| Max I/O Voltage | 1.2mV |
| Number of Amplifiers | 2 |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Supplier Device Package | 8-SOIC |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Base Part Number | TLV2402 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 900nA |
| Nominal Supply Current | 1.98μA |
| Power Dissipation | 710mW |
| Output Current | 200μA |
TLV2402CDR Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. Op amps are General Purpose types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. It has 8 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 1.2mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. The buffer amplifier is capable of operating from a supply current of 900nA . There should be no change in the voltage gain. This op amp contains 2 circuits. As far as the device is concerned, buffer amplifier has 2 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. This instrumentation amplifier cannot operate below -40°C degrees Celsius. A temperature greater than 125°C should not be used for the operation of buffer amplifier. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. The operating supply voltage of instrumentation amplifier is rated 8V voltage. A supply of 900nA or higher is recommended for use with this electronic part. Regarding the voltage of the supply, this electrical part can work from a voltage as low as 16V, and this is an excellent feature. To keep the buffer amps' supply voltage higher than 2.5V. As a rule of thumb, you should conduct this electronic part under a dual voltage supply of 8V volts. On the linear amplifier, there are 2 amplifiers that are used.
TLV2402CDR Features
120dB voltage gain
Output Type: Rail-to-Rail
TLV2402CDR Applications
There are a lot of Texas Instruments TLV2402CDR Instrumentational OP Amps applications.
- Ultrasound transducers
- Vehicle electronics
- Switching amplifier
- MP3
- Inverse/same-phase proportional circuit
- Industrial control system
- Industrial applications including automation
- Strain gauges
- Television broadcasting equipment
- Power control
