TLV2422QDRG4Q1
| Parameters | |
|---|---|
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 3V |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100, LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2422 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 150μA |
| Power Dissipation | 725mW |
| Output Current | 50mA |
| Slew Rate | 0.02V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 52 kHz |
| Unity Gain BW-Nom | 46 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
TLV2422QDRG4Q1 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be at least 8 terminations this year. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 3V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, buffer amplifier rates 2mV voltage. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . As long as the supply current of the chip does not exceed 100μA, this op amp ic can operate. 120dB should remain the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There are a total of 2 elements in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 5V voltage. TR is adopted to pack the instrumentation amplifier. Buffer op amp series numbers are indicated by the Automotive, AEC-Q100, LinCMOS?.
TLV2422QDRG4Q1 Features
8 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2422QDRG4Q1 Applications
There are a lot of Texas Instruments TLV2422QDRG4Q1 Instrumentational OP Amps applications.
- High input resistance broadband
- Digital cameras
- Exponential operation circuits
- Radiation thermometry transducers
- Proportional operation circuits
- Scintillation detectors
- Commercial audio systems
- Industrial control system
- Television broadcasting equipment
- Power generator
