TLV2432QD
| Parameters | |
|---|---|
| Supply Voltage | 3V |
| Base Part Number | TLV2432 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Circuits | 2 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Output Current | 50mA |
| Slew Rate | 0.25V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 300μV |
| Bandwidth | 500 kHz |
| Gain Bandwidth Product | 550kHz |
| Unity Gain BW-Nom | 500 kHz |
| Voltage Gain | 119.55dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
TLV2432QD Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tube case. The number of terminations is approaching the 8 mark. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 3V battery. Instrumentation amplifier is a part of Operational Amplifier. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 300μV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Operational amplifier can operate supply current at 200μA. Keeping the voltage gain at 119.55dB is the best course of action. During the manufacturing process, this buffer amplifier is divided into 2 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage. For the packing of the instrumentation amplifier, TR is adopted. LinCMOS? is the number that corresponds to the series of the buffer op amp.
TLV2432QD Features
8 Pins
supply voltage of 3V
119.55dB voltage gain
Output Type: Rail-to-Rail
TLV2432QD Applications
There are a lot of Texas Instruments TLV2432QD Instrumentational OP Amps applications.
- Power control
- High/low-pass filter circuit
- Inverse/same-phase proportional circuit
- Scintillation detectors
- Switching amplifier
- Commercial audio systems
- Vehicle electronics
- Power transmission
- Automatic control
- High input resistance broadband
