TLV2442AQPW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLV2442 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 2.2mA |
| Power Dissipation | 525mW |
| Output Current | 50mA |
| Slew Rate | 1.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 950μV |
| Bandwidth | 1.75MHz |
| Gain Bandwidth Product | 1.81MHz |
| Unity Gain BW-Nom | 1810 kHz |
| Voltage Gain | 119.55dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 3V |
| Max I/O Voltage | 950μV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2442AQPW Overview
A 8-TSSOP (0.173, 4.40mm Width) case is used to package the op amp. A General Purpose-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. There have been a total of 8 terminations over the past year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 950μV. Surface Mount is the recommended mounting type of operational amplifiers. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 750μA, this op amp ic can operate. It is recommended to keep the voltage gain at 119.55dB at all times. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. There are 2 elements in total in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5V. It is used TR to pack the op amps. LinCMOS? corresponds to the op amp's series.
TLV2442AQPW Features
8 Pins
supply voltage of 3V
119.55dB voltage gain
Output Type: Rail-to-Rail
TLV2442AQPW Applications
There are a lot of Texas Instruments TLV2442AQPW Instrumentational OP Amps applications.
- Signal filtering
- Information processing
- Tablets
- Automatic control
- Automotive sensors
- Proportional operation circuits
- Broadcasting
- Video amplifiers
- ECG equipment
- Television
