TLV2442ID
| Parameters | |
|---|---|
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 1.75MHz |
| Gain Bandwidth Product | 1.81MHz |
| Unity Gain BW-Nom | 1810 kHz |
| Voltage Gain | 119.55dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 3V |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Number of Amplifiers | 4 |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2442 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 2.2mA |
| Power Dissipation | 725mW |
| Output Current | 50mA |
| Slew Rate | 1.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
TLV2442ID Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 2mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . An 750μA volt supply current is needed for this linear amplifier to operate. It is a member of the 119.55dB's 119.55dB family. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. There is a rating of 2 for the operating supply voltage of the buffer op amp. The operating supply voltage of the buffer op amp is rated at 5V. The LinCMOS? indicates the series number of the op amp. The buffer amplifier consists of 4 amplifiers.
TLV2442ID Features
8 Pins
supply voltage of 3V
119.55dB voltage gain
Output Type: Rail-to-Rail
TLV2442ID Applications
There are a lot of Texas Instruments TLV2442ID Instrumentational OP Amps applications.
- Power control
- RF cable systems
- earphone
- Division circuits
- Ultrasound transducers
- Multimedia playback equipment
- Wireless base stations
- Fast A/D and D/A converters
- Portable electronic products powered by batteries
- Portable media players
