TLV2450ID
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2450 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 42μA |
| Power Dissipation | 710mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Gain Bandwidth Product | 220kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00045μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
TLV2450ID Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tube case. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. Please take in mind that this instrumentation amplifier should be run at 3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 1.5mV for this buffer op amp. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . An 23μA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 103dB. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
TLV2450ID Features
8 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2450ID Applications
There are a lot of Texas Instruments TLV2450ID Instrumentational OP Amps applications.
- Voltage regulation circuit
- Non-polarized electrodes
- High input resistance broadband
- Power transmission
- High gain DC amplifier
- Portable media players
- Proportional counter tubes
- Differentiator circuits
- Band-stop filter
- Thermocouples
