TLV2451CDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2451 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 42μA |
| Power Dissipation | 385mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 220 kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2451CDBVT Overview
There is a SC-74A, SOT-753 case package that contains the instrumentation amplifiers. Op amps are General Purpose types of amplifier on the chip. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 5. A total of 5 pins are attached to buffer op amp. This linear amplifier should be powered by an 3V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 5 pins are present on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 1.5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 23μA, this op amp ic can operate. It is recommended to keep the voltage gain at 103dB at all times. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. This linear amplifier has a total of 1 elements. The operating supply voltage of the buffer op amp is rated at 3V. It is used TR to pack the op amps.
TLV2451CDBVT Features
5 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2451CDBVT Applications
There are a lot of Texas Instruments TLV2451CDBVT Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Band-pass filter
- Tablets
- Biopotential
- Video computer boards
- Signal transformation
- Large motor controllers
- PDA
- Digital cameras
- Signal amplification
