TLV2451ID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2451 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 42μA |
| Power Dissipation | 710mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 220 kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.00045μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2451ID Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. This is a General Purpose type op amp. Linear amplifier is delivered in a Tube case. The number of terminations approaches 8. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 8 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 1.5mV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . As long as the supply current of the chip does not exceed 23μA, this op amp ic can operate. 103dB should remain the voltage gain. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. There is a rating of 1 for the operating supply voltage of the buffer op amp. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
TLV2451ID Features
8 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2451ID Applications
There are a lot of Texas Instruments TLV2451ID Instrumentational OP Amps applications.
- Large motor controllers
- Industrial control system
- Signal transformation
- Proportional counter tubes
- Proportional operation circuits
- PDA
- Division circuits
- Tablets
- pH (acidity)
- Medical instruments
