TLV2451IDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2451 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 42μA |
| Power Dissipation | 385mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 220 kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2451IDBVT Overview
In the package, you will find a SC-74A, SOT-753-case to contain the op amp ic. An op amp of this type is a General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 5 terminations have been reported in the past few weeks. It consists of a total of 5 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 5 pins. Regarding input offset voltage, buffer amplifier rates 1.5mV voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. You can run this op amp ic on 23μA . 103dB should be the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. As a whole, there are 1 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 3V voltage. The linear amplifier is packaged by using a TR axis.
TLV2451IDBVT Features
5 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2451IDBVT Applications
There are a lot of Texas Instruments TLV2451IDBVT Instrumentational OP Amps applications.
- Fission chambers
- Test and measurement instruments
- Video computer boards
- Fast A/D and D/A converters
- Mobile phone
- Inverse/same-phase proportional circuit
- Comparator
- Integrator circuits
- Video conversion and routing
- Wireless base stations
