TLV2454AIPWR
| Parameters | |
|---|---|
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Base Part Number | TLV2454 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 4 |
| Power Supplies | +-1.35/+-3/2.7/6V |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 168μA |
| Power Dissipation | 720mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 220 kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1mV |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
TLV2454AIPWR Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. A Cut Tape (CT) case is used for delivering the op amp. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 3V battery. It should be noted that this op amp is a type of Operational Amplifier device. The buffer op amp includes 14 pins. In terms of input offset voltage, operational amplifier rates 1mV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . Using an 23μA supply current, this operational amplifier ics can be operated. Maintain 103dB as the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. A total of 4 elements are present in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 3V. A TR-shaped amplifier is used to pack the buffer amps.
TLV2454AIPWR Features
14 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2454AIPWR Applications
There are a lot of Texas Instruments TLV2454AIPWR Instrumentational OP Amps applications.
- Proportional counter tubes
- High/low-pass filter circuit
- Radiation thermometry transducers
- High speed sample
- MP3
- Laptop
- Division circuits
- Broadcasting
- Industrial applications including automation
- Car stereo
