TLV2454IPWR
| Parameters | |
|---|---|
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Base Part Number | TLV2454 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 4 |
| Power Supplies | +-1.35/+-3/2.7/6V |
| Operating Supply Current | 23μA |
| Nominal Supply Current | 168μA |
| Power Dissipation | 720mW |
| Output Current | 10mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 220 kHz |
| Unity Gain BW-Nom | 220 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 300μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Height | 1.2mm |
TLV2454IPWR Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. An op amp ic of the General Purpose type. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. A total of 14 terminations have been reported in the past few weeks. In this case, there are 14 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 14 pins that make up the linear amplifier. Op amp ic rates 1.5mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. The buffer amplifier is capable of operating from a supply current of 23μA . Keeping the voltage gain at 103dB is the best course of action. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. This linear amplifier has a total of 4 elements. The operating supply voltage of instrumentation amplifier is rated 3V voltage. A TR-shaped amplifier is used to pack the buffer amps.
TLV2454IPWR Features
14 Pins
supply voltage of 3V
103dB voltage gain
Output Type: Rail-to-Rail
TLV2454IPWR Applications
There are a lot of Texas Instruments TLV2454IPWR Instrumentational OP Amps applications.
- Micro signal measurement
- Signal filtering
- MP3
- Tablets
- Wireless base stations
- Comparator
- Commercial audio systems
- Polarized electrodes
- Large motor controllers
- High speed sample
