TLV2460AIP
| Parameters | |
|---|---|
| Nominal Supply Current | 650μA |
| Power Dissipation | 1.2W |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 5200 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TLV2460 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 550μA |
TLV2460AIP Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. An op amp of this type is a General Purpose-type. A Tube case is used to deliver the buffer op amp. There is a growing number of terminations approaching the number of 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 1.5mV. The mounting type that is recommended for this electrical part is Through Hole. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . An 550μA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 109dB for the time being. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The linear amplifier consists of 1 different elements in total. The operating supply voltage of the buffer op amp is rated at 3V.
TLV2460AIP Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2460AIP Applications
There are a lot of Texas Instruments TLV2460AIP Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Video data acquisition
- Non-polarized electrodes
- Test and measurement instruments
- E-book readers
- Home audio systems
- Multimedia playback equipment
- Micro signal measurement
- High/low-pass filter circuit
- Voltage regulation circuit
