TLV2460CDBVR
| Parameters | |
|---|---|
| Average Bias Current-Max (IIB) | 0.025μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | TLV2460 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 650μA |
| Power Dissipation | 425mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 71 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
TLV2460CDBVR Overview
In order to protect the op amps, a SOT-23-6 case is used. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. The number of terminations approaches 6. A total of 6 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 3V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 6 pins are present on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 2mV voltage. Surface Mount is the recommended mounting type of operational amplifiers. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . This op amp can operate from a supply current at 550μA. There should be no change in the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. 1 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 3V voltage. It is used TR to pack the op amps.
TLV2460CDBVR Features
6 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2460CDBVR Applications
There are a lot of Texas Instruments TLV2460CDBVR Instrumentational OP Amps applications.
- Computer workstations
- Logarithmic operation circuits
- Industrial control system
- Addition operation circuits
- Communication device
- Semiconductor detectors
- PDA
- Radar
- Medical instruments
- Instrumentation
