Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
0°C~70°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.95mm |
Base Part Number |
TLV2460 |
Pin Count |
6 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
3V |
Number of Elements |
1 |
Operating Supply Current |
550μA |
Nominal Supply Current |
650μA |
Power Dissipation |
425mW |
Output Current |
80mA |
Slew Rate |
1.6V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
71 dB |
Current - Input Bias |
1.3nA |
Voltage - Supply, Single/Dual (±) |
2.7V~6V ±1.35V~3V |
Output Current per Channel |
80mA |
Input Offset Voltage (Vos) |
2mV |
Bandwidth |
6.4MHz |
Unity Gain BW-Nom |
6400 kHz |
Voltage Gain |
109dB |
Average Bias Current-Max (IIB) |
0.025μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Voltage - Input Offset |
500μV |
Low-Bias |
NO |
Micropower |
NO |
Programmable Power |
NO |
Max I/O Voltage |
2mV |
Input Offset Current-Max (IIO) |
0.007μA |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TLV2460CDBVT Overview
In order to protect the op amps, a SOT-23-6 case is used. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 6. The total number of pins on linear amplifier is 6. It is important to remember that this op amp should be operated at a voltage of 3V volts. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 6 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 550μA, this op amp ic can operate. There should be no change in the voltage gain at 109dB. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. A voltage rating of 1 is indicated for the op amp's operating supply voltage. The operating supply voltage of instrumentation amplifier is rated 3V voltage. This linear amplifier pack is based on the TR axis.
TLV2460CDBVT Features
6 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2460CDBVT Applications
There are a lot of Texas Instruments TLV2460CDBVT Instrumentational OP Amps applications.
- Subtraction operation circuits
- Test and measurement instruments
- ECG equipment
- Broadcasting
- Biopotential
- E-book readers
- Displayers for aircraft and air transportation control systems
- Band-stop filter
- Exponential operation circuits
- Video data acquisition