TLV2461IDBVTG4
| Parameters | |
|---|---|
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TLV2461 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 650μA |
| Power Dissipation | 385mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
TLV2461IDBVTG4 Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 5 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 5. As a reminder, this buffer op amp should be powered by 3V battery and that the battery should be inserted in the amplifier. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. It has 5 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 2mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, this op amp functions well at -40°C~125°C. You can run this op amp ic on 550μA . You should keep the voltage gain at 109dB for the time being. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The total number of elements in this buffer amplifier is 1. The operating supply voltage of instrumentation amplifier is rated 3V voltage. The linear amplifier is packaged by using a TR axis.
TLV2461IDBVTG4 Features
5 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2461IDBVTG4 Applications
There are a lot of Texas Instruments TLV2461IDBVTG4 Instrumentational OP Amps applications.
- High input resistance broadband
- Proportional counter tubes
- Hand-held batteries
- Television
- Fission chambers
- Power control
- Information processing
- Tablets
- High gain DC amplifier
- Signal amplification
