TLV2462AID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 710mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 5.2MHz |
| Gain Bandwidth Product | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.5mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2462AID Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. An op amp of this type is a General Purpose-type. There is a Tube case that is delivered with the instrumentation amplifiers. The number of terminations is approaching the 8 mark. It consists of a total of 8 pins in total. I would like to remind you that this buffer op amp should be powered by an 3V battery. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 1.5mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. It is possible to operate this buffer amplifier from a supply current of 550μA . You should keep the voltage gain at 109dB for the time being. On the buffer amps, there are 2 channels that can be used. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
TLV2462AID Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462AID Applications
There are a lot of Texas Instruments TLV2462AID Instrumentational OP Amps applications.
- Polarized electrodes
- Large motor controllers
- Measurements of Wheatstone bridge
- High speed sample
- Weak signal detection
- Non-polarized electrodes
- Test and measurement instruments
- Commercial audio systems
- Industrial control system
- Biopotential
