TLV2462CDGK
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 481mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2462CDGK Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. Linear amplifier is delivered in a Tube case. The number of terminations approaches 8. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are included on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 2mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. Using an 550μA supply current, this operational amplifier ics can be operated. 109dB should remain the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. 2 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 3V.
TLV2462CDGK Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462CDGK Applications
There are a lot of Texas Instruments TLV2462CDGK Instrumentational OP Amps applications.
- Video computer boards
- Signal amplification
- Exponential operation circuits
- Biopotential
- Signal filtering
- ECG equipment
- E-book readers
- Semiconductor detectors
- PDA
- Ultrasound transducers
