TLV2462IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 710mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2462IDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 3V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are included on the operational amplifiers. There is an input offset voltage of 2mV for this buffer op amp. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThis op amp can operate from a supply current at 550μA. There should be no change in the voltage gain at 109dB. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 3V. For packing the buffer amplifier, the TR-axis is adopted.
TLV2462IDR Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462IDR Applications
There are a lot of Texas Instruments TLV2462IDR Instrumentational OP Amps applications.
- Portable media players
- Video computer boards
- Micro signal measurement
- Strain gauges
- Vehicle electronics
- Industrial applications including automation
- Car stereo
- Hand-held batteries
- Weak signal detection
- Radiation thermometry transducers
