TLV2462IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 1.2W |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2462IP Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. This is a General Purpose type op amp. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 3V volts. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. This electronic part is recommended for mounting type Through Hole. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIt is possible to operate this buffer amplifier from a supply current of 550μA . You should keep the voltage gain at 109dB for the time being. On the output type, there are Rail-to-Rail different types of op amps. A total of 2 elements are present in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
TLV2462IP Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462IP Applications
There are a lot of Texas Instruments TLV2462IP Instrumentational OP Amps applications.
- Proportional counter tubes
- Polarized electrodes
- Digital cameras
- Television broadcasting equipment
- Portable electronic products powered by batteries
- High speed sample
- PDA
- Weighing systems
- Non-polarized electrodes
- E-book readers
