TLV2462QDRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.000075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 150μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2462QDRQ1 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. Buffer amplifier has a total of 8 pins on it. Please take in mind that op amp should be run at 3V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. In total, the buffer amplifier consists of 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using a supply current of 550μA , this buffer op amp will be able to operate. Keeping the voltage gain at 109dB is the best course of action. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. 2 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 3V. An buffer amplifier is packed in a TR-shape according to the design. Automotive, AEC-Q100 is the number that corresponds to the series of the buffer op amp.
TLV2462QDRQ1 Features
8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462QDRQ1 Applications
There are a lot of Texas Instruments TLV2462QDRQ1 Instrumentational OP Amps applications.
- Vehicle electronics
- Video amplifiers
- Hand-held batteries
- Video data acquisition
- Digital cameras
- High input resistance broadband
- Logarithmic operation circuits
- Band-pass filter
- Test and measurement instruments
- Inverse/same-phase proportional circuit
