TLV2464CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLV2464 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 4 |
| Power Supplies | +-1.35/+-3/2.7/6V |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 2.6mA |
| Power Dissipation | 1.022W |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.025μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2464CDR Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. General Purpose-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used to deliver the buffer op amp. We are approaching the 14h termination of the year. The pins on this board total to 14 in total. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 14-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 2mV. For this electrical component, Surface Mount is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . As long as the supply current of the chip does not exceed 550μA, this op amp ic can operate. Voltage gain should remain at 109dB. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. A total of 4 elements are present in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 3V. To pack the operational amplifier ics, TR is adopted as the packing method.
TLV2464CDR Features
14 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2464CDR Applications
There are a lot of Texas Instruments TLV2464CDR Instrumentational OP Amps applications.
- Switching amplifier
- Home audio systems
- Division circuits
- Portable electronic products powered by batteries
- Differentiator circuits
- Communication
- Addition operation circuits
- Tablets
- Multiplication circuits
- Displayers for aircraft and air transportation control systems
