TLV2470AIP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TLV2470 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 600μA |
| Nominal Supply Current | 900μA |
| Power Dissipation | 1.2W |
| Output Current | 35mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 61 dB |
| Current - Input Bias | 2.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 1.6mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.6mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2470AIP Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. An op amp of this type is a General Purpose-type. A Tube case is used to deliver the buffer op amp. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 3V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 1.6mV. Through Hole is the recommended mounting type for this linear amplifier. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . This op amp can operate from a supply current at 600μA. The voltage gain should stay at 120dB. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. There are 1 elements in this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
TLV2470AIP Features
8 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2470AIP Applications
There are a lot of Texas Instruments TLV2470AIP Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- High input resistance broadband
- Band-pass filter
- Portable docking station
- Television broadcasting equipment
- Strain gauges
- Test and measurement instruments
- Communication
- Portable electronic products powered by batteries
- Multimedia playback equipment
