TLV2470CP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TLV2470 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 1 |
| Operating Supply Current | 600μA |
| Nominal Supply Current | 900μA |
| Power Dissipation | 1.2W |
| Output Current | 35mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 61 dB |
| Current - Input Bias | 2.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 2.2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 2.2mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2470CP Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. A Tube case is used to deliver the buffer op amp. A total of 8 terminations have been reported in the past few weeks. Linear amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are included on the operational amplifiers. Regarding input offset voltage, op amp rates 2.2mV. The mounting type that is recommended for this electrical part is Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of 0°C~70°C. Using a supply current of 600μA , this buffer op amp will be able to operate. There should be no change in the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. There is a rating of 1 for the operating supply voltage of the buffer op amp. The operating supply voltage of the buffer op amp is rated at 3V.
TLV2470CP Features
8 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2470CP Applications
There are a lot of Texas Instruments TLV2470CP Instrumentational OP Amps applications.
- Proportional counter tubes
- pH (acidity)
- Video data acquisition
- Signal transformation
- Car stereo
- Addition operation circuits
- Medical imaging
- Mobile phone
- Band-stop filter
- Laptop
