TLV2473AIN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV2473 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 2 |
| Operating Supply Current | 600μA |
| Nominal Supply Current | 1.8mA |
| Power Dissipation | 1.6W |
| Output Current | 35mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 61 dB |
| Current - Input Bias | 2.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 1.6mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 1.6mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2473AIN Overview
Packaging for the buffer amplifier is in the form of a 14-DIP (0.300, 7.62mm) case. An op amp ic of the General Purpose type. A Tube case is used to deliver the buffer op amp. The number of terminations is approaching the 14 mark. A total of 14 pins are located on this board. This linear amplifier should be powered by an 3V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 14 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 1.6mV. Through Hole is the recommended mounting type of operational amplifiers. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. The buffer amplifier is capable of operating from a supply current of 600μA . You should keep the voltage gain at 120dB for the time being. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. Op amp has total of 2 elements. The operating supply voltage of the buffer op amp is rated at 3V.
TLV2473AIN Features
14 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2473AIN Applications
There are a lot of Texas Instruments TLV2473AIN Instrumentational OP Amps applications.
- Fast A/D and D/A converters
- Inverse/same-phase proportional circuit
- Radar
- Power control
- Fission chambers
- Band-pass filter
- Displayers for aircraft and air transportation control systems
- Radiation thermometry transducers
- High speed sample
- Weak signal detection
