TLV271CDBVR
| Parameters | |
|---|---|
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLV271 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 1 |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 800μA |
| Power Dissipation | 201mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 69 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.45mm |
TLV271CDBVR Overview
Packaging for the buffer amplifier is in the form of a SC-74A, SOT-753 case. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used for delivering the op amp. There is a growing number of terminations approaching the number of 5. The pins on this board total to 5 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 5 pins. In terms of input offset voltage, operational amplifier rates 5mV. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureYou can run this op amp ic on 625μA . 110dB should remain the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There are 1 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 8V voltage. For packing the buffer amplifier, the TR-axis is adopted.
TLV271CDBVR Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV271CDBVR Applications
There are a lot of Texas Instruments TLV271CDBVR Instrumentational OP Amps applications.
- Division circuits
- pH (acidity)
- E-book readers
- Video conversion and routing
- Television broadcasting equipment
- Micro signal measurement
- Test and measurement instruments
- Medical instruments
- Non-polarized electrodes
- Comparator
