TLV271QDRG4Q1
| Parameters | |
|---|---|
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 5mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Base Part Number | TLV271 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Circuits | 1 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 800μA |
| Output Current | 13mA |
| Slew Rate | 2.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 58 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
TLV271QDRG4Q1 Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations approaches 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 2.7V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 8 pins on this chip. Op amp rates 500μV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . An 750μA volt supply current is needed for this linear amplifier to operate. Maintain 110dB as the voltage gain. On this instrumentation amplifier, there are 1 circuits that are connected together. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of instrumentation amplifier is rated 8V voltage. A TR-shaped amplifier is used to pack the buffer amps. The Automotive, AEC-Q100 stands for the buffer op amp's serial number.
TLV271QDRG4Q1 Features
8 Pins
supply voltage of 2.7V
110dB voltage gain
Output Type: Rail-to-Rail
TLV271QDRG4Q1 Applications
There are a lot of Texas Instruments TLV271QDRG4Q1 Instrumentational OP Amps applications.
- Medical imaging
- Video data acquisition
- Computer workstations
- Image computer boards
- Polarized electrodes
- Vehicle electronics
- Automation control systems
- Automotive sensors
- Weak signal detection
- PDA
