TLV272CDGKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 250mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLV272 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 1.6mA |
| Power Dissipation | 250mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 58 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 2.4MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV272CDGKR Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. A CMOS-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 5mV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . Using a supply current of 625μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 110dB at all times. There are 2 channels on the operational amplifiers. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of instrumentation amplifier is rated 5V voltage. A TR-shaped amplifier is used to pack the buffer amps.
TLV272CDGKR Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV272CDGKR Applications
There are a lot of Texas Instruments TLV272CDGKR Instrumentational OP Amps applications.
- Radiation thermometry transducers
- Addition operation circuits
- Large motor controllers
- Mobile phone
- Professional videography
- Measurements of Wheatstone bridge
- Automatic control
- Displayers for aircraft and air transportation control systems
- Active probe
- Weak signal detection
