Parameters |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Dual Supply Voltage |
5V |
Nominal Gain Bandwidth Product |
2.4MHz |
Max I/O Voltage |
5mV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
1.75mm |
Length |
4.9mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Max Power Dissipation |
396mW |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
TLV272 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Operating Supply Current |
625μA |
Nominal Supply Current |
1.6mA |
Power Dissipation |
396mW |
Output Current |
13mA |
Slew Rate |
2.6V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
CMOS |
Common Mode Rejection Ratio |
58 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
2.7V~16V ±1.35V~8V |
Output Current per Channel |
13mA |
Input Offset Voltage (Vos) |
5mV |
Bandwidth |
3MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
3000 kHz |
Voltage Gain |
110dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Power Supply Rejection Ratio (PSRR) |
70dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
500μV |
Current - Output / Channel |
8mA |
TLV272ID Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. CMOS-type instrumentation amplifiers are used in this application. There is a Tube case that is delivered with the instrumentation amplifiers. It is estimated that there will be at least 8 terminations this year. It consists of a total of 8 pins in total. It is important to remember that this op amp should be operated at a voltage of 5V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. An 625μA volt supply current is needed for this linear amplifier to operate. The voltage gain should stay at 110dB. On the buffer amps, there are 2 channels that can be used. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage.
TLV272ID Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV272ID Applications
There are a lot of Texas Instruments TLV272ID Instrumentational OP Amps applications.
- Comparator
- earphone
- Automotive sensors
- Polarized electrodes
- High speed sample
- High input resistance broadband
- Signal amplification
- Division circuits
- Band-pass filter
- Large motor controllers