TLV272IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLV272 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 1.6mA |
| Power Dissipation | 625mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 58 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 16V |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 2.4MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV272IP Overview
There is a 8-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the CMOS-type. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. This electronic part is best mounted with type Through Hole. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAn 625μA volt supply current is needed for this linear amplifier to operate. 110dB should be the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5V.
TLV272IP Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV272IP Applications
There are a lot of Texas Instruments TLV272IP Instrumentational OP Amps applications.
- ECG equipment
- Hand-held batteries
- Automatic control
- Proportional operation circuits
- Comparator
- Wireless base stations
- High speed sample
- Signal amplification
- Micro signal measurement
- Video computer boards
