Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
14 |
Operating Temperature |
-40°C~125°C |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Max Power Dissipation |
531mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Base Part Number |
TLV274 |
Pin Count |
14 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
5V |
Power Supplies |
+-1.35/+-8/2.7/16V |
Number of Channels |
4 |
Operating Supply Current |
625μA |
Nominal Supply Current |
3.2mA |
Power Dissipation |
531mW |
Output Current |
13mA |
Slew Rate |
2.6V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
69 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
2.7V~16V ±1.35V~8V |
Output Current per Channel |
13mA |
Input Offset Voltage (Vos) |
5mV |
Bandwidth |
3MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
3000 kHz |
Voltage Gain |
110dB |
Average Bias Current-Max (IIB) |
0.00006μA |
Power Supply Rejection Ratio (PSRR) |
70dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
500μV |
Current - Output / Channel |
8mA |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00006μA |
Programmable Power |
NO |
Dual Supply Voltage |
5V |
Nominal Gain Bandwidth Product |
3MHz |
Max I/O Voltage |
5mV |
Input Offset Current-Max (IIO) |
0.00006μA |
Height |
1.75mm |
Length |
8.65mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TLV274IDR Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. A Cut Tape (CT) case is used to deliver the buffer op amp. It is estimated that there will be 14 terminations in the next few months. The pins on this board total to 14 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. An 14-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, op amp ranges -40°C~125°C. You can run this op amp ic on 625μA . There should be no change in the voltage gain. Buffer op amp is equipped with 4 channels on the device. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 5V. A TR-shaped amplifier is used to pack the buffer amps.
TLV274IDR Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV274IDR Applications
There are a lot of Texas Instruments TLV274IDR Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Active probe
- Signal transformation
- Professional videography
- Multiplication circuits
- Differentiator circuits
- Non-polarized electrodes
- Proportional operation circuits
- Cinema or auditorium audio system
- Logarithmic operation circuits