TLV274IPW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | TLV274 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 4 |
| Power Supplies | +-1.35/+-8/2.7/16V |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 3.2mA |
| Power Dissipation | 374mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 69 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV274IPW Overview
A 14-TSSOP (0.173, 4.40mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. A Tube case is used for delivering the op amp. There have been a total of 14 terminations over the past year. A total of 14 pins are located on this board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 14 pins are available on the instrumentation amplifier. The input offset voltage is 5mV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . A supply current of 625μA can be used to operate this linear amplifier. There should be no change in the voltage gain at 110dB. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The buffer op amp is rated for an operating voltage of 4 when it comes to the power supply. The operating supply voltage of instrumentation amplifier is rated 5V voltage.
TLV274IPW Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV274IPW Applications
There are a lot of Texas Instruments TLV274IPW Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Biopotential
- Power control
- Test equipment
- Video amplifiers
- Differentiator circuits
- Blood pressure sensors
- Industrial applications including automation
- Hand-held batteries
- Large motor controllers
