TLV2760ID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.4V |
| Base Part Number | TLV2760 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 28μA |
| Power Dissipation | 710mW |
| Output Current | 10.2mA |
| Slew Rate | 0.23V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~3.6V ±0.9V~1.8V |
| Output Current per Channel | 10.2mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 500 kHz |
| Unity Gain BW-Nom | 500 kHz |
| Voltage Gain | 101.58dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 4V |
| Voltage - Input Offset | 550μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 500 kHz |
| Max I/O Voltage | 3.5mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2760ID Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. This is a General Purpose type op amp. There is a Tube case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 2.4V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 3.5mV. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . You can run this op amp ic on 20μA . You should keep the voltage gain at 101.58dB for the time being. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The linear amplifier consists of 1 different elements in total.
TLV2760ID Features
8 Pins
supply voltage of 2.4V
101.58dB voltage gain
Output Type: Rail-to-Rail
TLV2760ID Applications
There are a lot of Texas Instruments TLV2760ID Instrumentational OP Amps applications.
- Thermocouples
- Multiplication circuits
- Cinema or auditorium audio system
- Differentiator circuits
- Power generator
- Addition operation circuits
- Measurements of Wheatstone bridge
- ECG equipment
- PDA
- Video conversion and routing
