TLV2770IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Base Part Number | TLV2770 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 2.7/5V |
| Number of Circuits | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 2mA |
| Output Current | 50mA |
| Slew Rate | 10.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 5.1MHz |
| Unity Gain BW-Nom | 5100 kHz |
| Voltage Gain | 113.06dB |
| Average Bias Current-Max (IIB) | 0.00035μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 5.1MHz |
| Max I/O Voltage | 2.5mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2770IDR Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations approaches 8. A total of 8 pins are located on this board. The linear amplifier should be run at 2.7V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The op amp ic has an array of 8 pins on it. Op amp rates 500μV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . As long as the supply current of the chip does not exceed 1mA, this op amp ic can operate. There should be no change in the voltage gain. A linear amplifier like this has 1 circuits on it. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 3V voltage. The instrumentation amplifier is packed in the form of TR.
TLV2770IDR Features
8 Pins
supply voltage of 2.7V
113.06dB voltage gain
Output Type: Rail-to-Rail
TLV2770IDR Applications
There are a lot of Texas Instruments TLV2770IDR Instrumentational OP Amps applications.
- Signal filtering
- Large motor controllers
- Band-stop filter
- Exponential operation circuits
- Image computer boards
- Commercial audio systems
- Power transmission
- Scintillation detectors
- Division circuits
- Hand-held batteries
