TLV2780IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Base Part Number | TLV2780 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 650μA |
| Nominal Supply Current | 770μA |
| Power Dissipation | 710mW |
| Output Current | 23mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 2.5pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~3.6V ±0.9V~1.8V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 8MHz |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 4V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 8MHz |
| Max I/O Voltage | 3mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2780IDR Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations is approaching the 8 mark. The pins on this board total to 8 in total. It is important to remember that this op amp should be operated at a voltage of 2.7V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureOperational amplifier can operate supply current at 650μA. Maintain 120dB as the voltage gain. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. There is a rating of 1 for the operating supply voltage of the buffer op amp. A TR-shaped amplifier is used to pack the buffer amps.
TLV2780IDR Features
8 Pins
supply voltage of 2.7V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2780IDR Applications
There are a lot of Texas Instruments TLV2780IDR Instrumentational OP Amps applications.
- Integrator circuits
- Strain gauges
- Digital cameras
- Signal filtering
- Communication
- Laptop
- Instrumentation
- Portable electronic products powered by batteries
- Portable media players
- Weak signal detection
