TLV2783IN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Base Part Number | TLV2783 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | +-0.9/+-1.8/1.8/3.6V |
| Operating Supply Current | 650μA |
| Nominal Supply Current | 1.54mA |
| Power Dissipation | 1.6W |
| Output Current | 23mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 2.5pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~3.6V ±0.9V~1.8V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 8MHz |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 4V |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000015μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 8MHz |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 0.000015μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2783IN Overview
A 14-DIP (0.300, 7.62mm) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. A Tube case is used to deliver the buffer op amp. It is estimated that there will be 14 terminations in the next few months. It consists of a total of 14 pins in total. Please take in mind that this instrumentation amplifier should be run at 2.7V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 14 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 3mV. The mounting type that is recommended for this electrical part is Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. Operational amplifier can operate supply current at 650μA. The voltage gain should stay at 120dB. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. There is a rating of 2 for the operating supply voltage of the buffer op amp.
TLV2783IN Features
14 Pins
supply voltage of 2.7V
120dB voltage gain
Output Type: Rail-to-Rail
TLV2783IN Applications
There are a lot of Texas Instruments TLV2783IN Instrumentational OP Amps applications.
- High gain DC amplifier
- Comparator
- Vehicle electronics
- Test and measurement instruments
- Proportional operation circuits
- Hand-held batteries
- Thermocouples
- High/low-pass filter circuit
- Car stereo
- Video data acquisition
