TLV27L2ID
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLV27L2 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 2 |
| Operating Supply Current | 7μA |
| Nominal Supply Current | 22μA |
| Power Dissipation | 710mW |
| Output Current | 400μA |
| Slew Rate | 0.06V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 71 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 400μA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 160 kHz |
| Unity Gain BW-Nom | 160 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.001μA |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 16.5V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 160 kHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIMOS |
TLV27L2ID Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. The pins on this board total to 8 in total. This linear amplifier should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. An 7μA volt supply current is needed for this linear amplifier to operate. It is a member of the 100dB's 100dB family. There are a total of 2 channels available on the op amps. On the output type, there are Rail-to-Rail different types of op amps. The operating supply voltage of instrumentation amplifier is rated 8V voltage.
TLV27L2ID Features
8 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
TLV27L2ID Applications
There are a lot of Texas Instruments TLV27L2ID Instrumentational OP Amps applications.
- Laptop
- Biopotential
- Video data acquisition
- Division circuits
- Proportional operation circuits
- Exponential operation circuits
- Weak signal detection
- Communication device
- Displayers for aircraft and air transportation control systems
- Subtraction operation circuits
