TLV341IDCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TLV341 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 75μA |
| Nominal Supply Current | 150μA |
| Output Current | 115mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.5V~5.5V |
| Output Current per Channel | 115mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 2.2MHz |
| Gain Bandwidth Product | 2.3MHz |
| Unity Gain BW-Nom | 2200 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 300μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 2.2MHz |
| Max I/O Voltage | 4mV |
| Power | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV341IDCKR Overview
The linear amplifier is packaged in a 6-TSSOP, SC-88, SOT-363 case. An op amp of this type is a General Purpose-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 6. The total number of pins on linear amplifier is 6. I would like to remind you that this buffer op amp should be powered by an 1.8V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. It has 6 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 4mV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAn 75μA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 110dB at all times. On the output type, there are Rail-to-Rail different types of op amps. It is possible to count 1 elements on this buffer amplifier. For packing the buffer amplifier, the TR-axis is adopted.
TLV341IDCKR Features
6 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
TLV341IDCKR Applications
There are a lot of Texas Instruments TLV341IDCKR Instrumentational OP Amps applications.
- Video amplifiers
- Power control
- Video data acquisition
- High gain DC amplifier
- Exponential operation circuits
- Comparator
- Displayers for aircraft and air transportation control systems
- pH (acidity)
- Television broadcasting equipment
- RF cable systems
