Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Mounting Type |
Through Hole |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
0°C~70°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Technology |
CMOS |
Terminal Position |
DUAL |
Number of Functions |
2 |
Supply Voltage |
3V |
Base Part Number |
TLV4112 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Number of Elements |
2 |
Power Supplies |
3/5V |
Operating Supply Current |
700μA |
Nominal Supply Current |
2mA |
Power Dissipation |
1.2W |
Output Current |
320mA |
Slew Rate |
1.57V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
63 dB |
Current - Input Bias |
0.3pA |
Voltage - Supply, Single/Dual (±) |
2.5V~6V |
Output Current per Channel |
320mA |
Input Offset Voltage (Vos) |
3.5mV |
Bandwidth |
2.7MHz |
Unity Gain BW-Nom |
2700 kHz |
Voltage Gain |
110dB |
Average Bias Current-Max (IIB) |
0.0001μA |
Power Supply Rejection Ratio (PSRR) |
70dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Voltage - Input Offset |
175μV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00005μA |
Programmable Power |
NO |
Max I/O Voltage |
3.5mV |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TLV4112CP Overview
There is a 8-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. An op amp ic of the General Purpose type. There is a Tube case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. Linear amplifier includes 8 pins. In terms of input offset voltage, operational amplifier rates 3.5mV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of 0°C~70°C. It is possible to operate this buffer amplifier from a supply current of 700μA . The voltage gain should stay at 110dB. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The linear amplifier consists of 2 different elements in total.
TLV4112CP Features
8 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
TLV4112CP Applications
There are a lot of Texas Instruments TLV4112CP Instrumentational OP Amps applications.
- Micro signal measurement
- Industrial control system
- Inverse/same-phase proportional circuit
- Weak signal detection
- Test and measurement instruments
- High-frequency data acquisition systems
- MP3
- Radiation thermometry transducers
- Switching amplifier
- Ultrasound transducers