TLV4112IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV4112 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 2mA |
| Output Current | 320mA |
| Slew Rate | 1.57V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 320mA |
| Input Offset Voltage (Vos) | 175μV |
| Bandwidth | 2.7MHz |
| Unity Gain BW-Nom | 2700 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 3.5mV |
| Power | YES |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV4112IP Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tube case. It is estimated that there will be 8 terminations in the next few months. In total, there are 8 pins on this op amp ic. The linear amplifier should be run at 3V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. The input offset voltage is 175μV. This electrical part should be mounted using type Through Hole. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 700μA . There should be no change in the voltage gain at 110dB. There are 2 circuits on this op amp. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
TLV4112IP Features
8 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
TLV4112IP Applications
There are a lot of Texas Instruments TLV4112IP Instrumentational OP Amps applications.
- Subtraction operation circuits
- Professional videography
- Tablets
- Addition operation circuits
- Comparator
- High input resistance broadband
- Micro signal measurement
- Proportional counter tubes
- Cinema or auditorium audio system
- Portable media players
