TLV4113CDGQR
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TLV4113 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 2mA |
| Output Current | 320mA |
| Slew Rate | 1.57V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 320mA |
| Input Offset Voltage (Vos) | 175μV |
| Bandwidth | 2.7MHz |
| Unity Gain BW-Nom | 2700 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 3.5mV |
| Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
TLV4113CDGQR Overview
Packaging for the buffer amplifier is in the form of a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad case. An op amp of this type is a General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 10. A total of 10 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. The buffer op amp includes 10 pins. In terms of input offset voltage, operational amplifier rates 175μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . As long as the supply current of the chip does not exceed 700μA, this op amp ic can operate. 110dB should remain the voltage gain. This op amp contains 2 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The instrumentation amplifier is packed in the form of TAPE AND REEL.
TLV4113CDGQR Features
10 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
TLV4113CDGQR Applications
There are a lot of Texas Instruments TLV4113CDGQR Instrumentational OP Amps applications.
- Thermocouples
- Differentiator circuits
- Band-pass filter
- Power control
- High/low-pass filter circuit
- Mobile phone
- High-frequency data acquisition systems
- Active probe
- Weighing systems
- Gaming industry
