TLV4113IDGQR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TLV4113 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 2mA |
| Power Dissipation | 2.39W |
| Output Current | 320mA |
| Slew Rate | 1.57V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 320mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 2.7MHz |
| Unity Gain BW-Nom | 2700 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 175μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 3.5mV |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV4113IDGQR Overview
Packaged in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. It comes in a Cut Tape (CT) case, which protects instrumentation amplifier from damage during delivery. We are approaching the 10h termination of the year. A total of 10 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The op amp ic has an array of 10 pins on it. In terms of input offset voltage, operational amplifier rates 3.5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. You can run this op amp ic on 700μA . Voltage gain should remain at 110dB. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. This linear amplifier has a total of 2 elements. As a result of this, the buffer amplifier is packed in TR.
TLV4113IDGQR Features
10 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
TLV4113IDGQR Applications
There are a lot of Texas Instruments TLV4113IDGQR Instrumentational OP Amps applications.
- Power transmission
- Multimedia playback equipment
- Fast A/D and D/A converters
- Weighing systems
- Professional videography
- Automatic control
- Polarized electrodes
- Hand-held batteries
- Inverse/same-phase proportional circuit
- Precision measurement
